Regular readers of my journal know that I have a few topics that are from time to time, I continue to new posts. In particular, the construction of houses and roads in the United States, walking around the city, the train theme, as well as stories about the work of the oil industry. Today I decided to add these headings another theme - the weapon. Actually, nothing new in this category do not have, because I already wrote a short story about the shooting range. Due to the fact that my home arsenal apocalypse a monster by the number of all kinds of weapons, and in the shooting range I constant frequenter, I decided from time to time to write about guns and "armory" life in the United States, a well as talk about the handling of the weapons and shooting technique.
Today is the second article on the topic of the armory - incomplete disassembly and cleaning of the gun Ruger SR9. In the comments, I would appreciate, if you are interested in this subject and what you want to see in the posts. 1. Weapons, as a woman, requires attention and care, without a weapon at the right time you fail. During each shot gun barrel undergoes huge stresses from pressure and temperature. Moreover, when burned gunpowder allocates mass elements that destroy the metal and cause it to corrode. Therefore, after each operation of weapons at the shooting range, it needs cleaning. To clean, you will need special tools, which include copper brushes, cleaning rod, Wisher, oil, and rags (pieces of cotton cloth). Because my arsenal of weapons includes a completely different calibers, I use standardized kits for cleaning weapons. Them I have three: a pistol, for cleaning rifles and shotguns for cleaning. Principle there is no difference, the only difference is in the brushes (for example, set the rifle they are much longer), and the length of the ramrod (barrel of the rifle is much longer than a pistol that requires more nozzles on the cleaning rod). These kits are sold in any gun shops, the price ranges from $ 10 to $ 100, depending on the configuration. This set cost me $ 29.99.
2 proceed to disassemble the gun. First, make sure the pistol is unloaded. Every year a lot of people killed and injured themselves while cleaning weapons due to neglect and lack of weapons safety.
So, after the store is deleted, and the chamber is empty - you can start. The first step is to take the bolt to its rearmost position and secure it with a lock. Then it is necessary to return the magazine spring in a flat position by forcing a lowering lever store down.
3 On the right side of the gun just above the trigger guard is a stud you want to drown in the body. You can use any relatively sharp object.
4 Once the stud is recessed from the left side of the gun it is necessary to completely pull out and remove. Hairpin easily pulled his hands, so foreign objects is required.
5 Now you need to remove the bolt from the locking pin and gently bring it back to its original position, and continue to move along the rails to remove it from the scope of the gun body.
6 Removing the bolt from the frame, we have the following picture. Right - a body (frame) gun in the center - it's bolt pistol.Then on the photo we see the pin, which we removed earlier, and shop. By the way, many people mean the same thing under the magazine clip and, in fact, are completely different things. So do not confuse Store with a holder. The photo - shop.
7 Now we need to remove all the arrangements with the shutter gun. To do this, we turn the valve on the rear sight, and take out the recoil spring, and then the trunk itself.
8 Trunk must be thoroughly cleaned. During firing capsule formulations vsplamenyayutsya and connected with a metal barrel, subjecting it to corrosion and modifying the reaction of the metal to stresses during the shots. In addition, a bullet in the process of moving the trunk rubs solid particles of soot, just wearing out the barrel, so all the powder fouling and combustion capsule formulations to remove.
To clean the barrel, we will use a brush copper desired size for the gun bottle brush diameter is 11 mm (caliber gun - 9 mm to 19). Copper brush is planted on the ramrod, which is bolted handle, but not for convenience. Ramrod is near the handle Swivel, allowing brush to rotate freely inside the barrel as it moves inside of the rifling of the barrel. Further we need special cleaning oil, gun oil and rags with Wisher (which I forgot to put in this picture).
9 Please lubricate the barrel cleaning oil, then thoroughly clean it, spending brush along the entire length of the barrel. Once a deposit is cleaned from the inside of the barrel, we take a cloth, greased gun oil, and vdevaem it in Wisher (actually, he was right in the photo). Carefully wipe the barrel spending ramrod with Wisher through it. If there is dirt on the cloth, then cleaned with the brush barrel bad. Repeat the procedure for cleaning the barrel again, as long as the cloth is not clean after wiring through the barrel.
10 Once the barrel shines like a cat's smile, it can be set aside.
11 Now it is necessary to clean the carbon deposits from himself bolt pistol and a return spring. To do this we will use only rags, cleaning greased with oil. If, for some reason, you need to remove a deposit, you can use a brush or broom, which, by the way, this set is not. In this case, no solid soot. By the way, if you use high-quality cartridges, then a deposit with any problems you will not. Typically, problems arise due to poor (usually cheaper) cartridges, which use low-quality powder.
12 According to the same manner as the shutter we will clean all the mechanisms at the frame of the gun. Here it is necessary to pay attention to the chamber, the receiver and the firing pin mechanism. All items are detachable and cleaned directly on the frame. Do complete disassembly gun is not recommended, except in cases of repair, complete disassembly of a negative impact on the life of parts and weapons in general.
13 After the parts of the gun cleaned and lubricated, it is necessary to remove excess oil from them, if any. Lack of oil - bad for moving the gun, but its over just as bad. Then you need to collect the gate in the opposite order: connect it to the frame and insert the locking pin. It is worth to note that at this gun recoil spring has a definite position, and vice versa can not embed it. This will cause malfunction of the mechanism and possible breakage or sticking valve.
For reassembling the stud bolt is necessary to take the rearmost position and secure it with a lock. Otherwise hairpin categorically refuses to return to his seat.
14 We now proceed to the cleaning shop. Part of the gas when firing enter a store, therefore its walls also has a deposit (and eventually dirt, dust and so forth.) That must be periodically removed. If you are performing a variety of tactical exercises in the dash, it is often in addition to all in the process of running around your shop will fall in the sand and dirt with a quick recharge. Usually in the process of practical shooting recharge occurs in the movement during exercise, so pick up stores from the ground after the exercise is completed. In addition, the shop should be lubricated in for a better performance of the spring. While this many would argue.
To disassemble the shop need to drown "button" on the bottom part, and then we remove the magazine cover by sliding it to the side. The cover is mounted on runners, like the gate of a gun. This should be done gently, closing his fingers free hand open bottom of the store, otherwise the spring to jump out of the store, like a jack-of-the-box.
15 Well, that's all, store disassembled.
16 After the store cleaned and lubricated, collect it.
17 Check the operation of all machinery again. Gun ready to fire.
18 The next time I'll tell you about the gun shop and its range of products and prices. We learn that it is necessary to have a buyer for the purchase of weapons in the United States, and how long it takes the purchase process over time.
In the fourth part, I plan to talk about the proper technique and the four methods chambering a cartridge in the chamber.
Well, then I'll talk about the right to bear arms, their receipt and laws.
If you have a desire to see a specific theme or type of weapon - evading in the comments.
No comments:
Post a Comment